Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Fence Installation: The San Antonio Owner’s Guide
Jerith fence installation in San Antonio typically runs $3,500 to $9,000 for a full residential project, depending on linear footage, gate count, and whether we’re replacing an existing fence or starting fresh. If you have a Jerith fence that’s leaning, rusting at the post line, or sporting a gate that drags, we can usually get a crew out within the week to look at it. Most owners discover the problem the way you probably did: the gate stopped latching after a hard rain, or a section started tilting after the soil shifted, and now the whole fence line looks tired.
We’re an independent San Antonio contractor, not affiliated with Jerith, but we install and repair Jerith aluminum and steel fence systems regularly across the city, from Stone Oak down to Alamo Ranch. The good news is Jerith builds a straightforward product: residential aluminum fencing with a powder-coated finish, steel posts, and hardware that’s available in standard sizes. The bad news is San Antonio’s soil and sun find the weak points faster than most climates do.
Which Jerith Models This Applies To
Jerith manufactures two primary residential lines: the Aluminum series, which covers most decorative and pool-code fencing, and the Steel series, used for heavier-duty perimeter and commercial-grade applications. Within those lines, you’ll find models like the Regency, Estate, and Montgomery, each with different picket spacing, top-rail profiles, and post dimensions. The quickest way to identify what you have is to check the inside of a gate post or the bottom rail for a small metal tag or stamped imprint. If that’s gone, measure the post diameter. Jerith residential aluminum posts are typically 2-inch or 2.5-inch square; steel posts run larger and feel noticeably heavier.
One gotcha we see constantly: Jerith’s pool-code fence models use a specific self-closing hinge and latch assembly that meets San Antonio’s local pool barrier requirements. A generic hinge from the hardware store will bolt on fine, but it won’t spring back the way code requires, and an inspector will flag it. When it matters, we source the Jerith-spec hinge or an equivalent that matches the spring tension and closing speed. For non-pool fencing, quality aftermarket post caps, brackets, and screws are indistinguishable from OEM and save real money without cutting lifespan.
Styles & brands we work with
Signs Your Jerith Fence Installation Is Failing
- Gate drags or won’t latch. The hinge post has shifted out of plumb, usually because the concrete footer was poured too shallow for San Antonio’s expanding clay soil. The fix is resetting the post, not adjusting the hinges.
- White chalky residue on rails or pickets. The powder coat is oxidizing, which happens faster here than in drier climates because of our humidity and hard water from irrigation overspray. It starts cosmetic, but once the aluminum oxidizes through the finish, you get pitting.
- Rust bleeding from screw heads or bracket edges. Jerith uses galvanized hardware, but after 10 to 15 years in San Antonio’s wet-dry cycles, the galvanization wears thin at contact points. Replacing hardware early prevents staining the surrounding finish.
- Section leaning or post wobble at the base. The post has sheared or loosened inside the concrete footer. We see this most on sloped lots where runoff undercuts the footing, especially in the Hill Country portions of the city.
- Pickets rattling or popping out of the top rail. The rubber gaskets inside the rail channels have dried and shrunk. It looks like a minor annoyance, but without those gaskets, pickets grind against the rail and wear through the powder coat.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For San Antonio homeowners, a full Jerith-style fence installation lands between $3,500 and $9,000. A simple replacement on flat terrain with one gate sits at the lower end; a larger yard with multiple gates, pool-code hardware, or post resets in rocky soil pushes toward the top. Linear footage drives most of the cost, but site access matters too: a tight side yard where we’re hand-digging instead of running an auger adds labor hours.
Every quote from us is a written price before work starts. No line items added after the crew arrives, no surprises when the holes hit limestone. The price includes removal and disposal of the old fence, new posts set in concrete to San Antonio frost-line and wind-load standards, the Jerith-compatible panels and hardware, gates hung and adjusted, and a full clean-up with a photo before we leave. Our 365-Day Done Right Promise applies to every installation. If something’s not right a year later, we make it right.
DIY or Call Us?
You can safely check a few things yourself: whether gates still self-close and latch, whether any post wobbles when you push on it, and whether screws are tight. What you shouldn’t do is reset a post in concrete without knowing San Antonio’s soil conditions, or swap pool-fence hardware for anything that isn’t code-compliant. A leaning post is usually a footing problem, not a fence problem, and guessing at the cause means doing the job twice.
If the issue is a single gate hinge or a few popped pickets, you might handle that on a Saturday with the right parts. If the problem is structural, you want someone who’s set hundreds of posts in this city’s dirt and stands behind the work. Call (432) 233-0976 and we’ll come take a look. The estimate’s free, and it’s written down before you decide anything.
FAQs
A properly installed Jerith-style aluminum fence lasts 20 to 30 years in San Antonio, but the powder-coated finish will likely show oxidation and chalkiness by the 10 to 15 year mark unless you keep irrigation overspray off the metal and rinse the panels once or twice a year. Hardware typically needs replacement around year 12 to 15. Call (432) 233-0976 if you’re seeing early rust or finish failure years sooner than that, because the problem is usually installation-related and worth correcting before it spreads.
Yes, a leaning section can usually be repaired by resetting the affected post in a deeper, wider concrete footing, which costs a fraction of a full fence replacement. The key is catching it before the post bends or shears at the base, so if a section is tilting, call (432) 233-0976 for an assessment rather than waiting.
A typical residential Jerith fence installation in San Antonio takes two to four days, depending on linear footage, gate count, and whether old posts need to be broken out and removed. Weather can stretch that, but we’ll tell you the schedule in writing before we start so you’re never guessing when the gate will close again.
We keep common Jerith-compatible hardware on our trucks and in the shop: gate hinges, latches, post caps, brackets, picket gaskets, and fasteners. For full panel replacement, we order the exact model match so the finish and profile align with your existing fence. Call (432) 233-0976 with your model info or measurements and we’ll let you know what’s in stock before you commit to anything.
Written by Graham Stein, Owner, Elmstead Remodeling San Antonio at Elmstead Remodeling San Antonio, serving San Antonio and nearby areas.
