Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Roofing: The San Antonio Owner’s Guide
We stock and install Barrette-compatible roofing parts across San Antonio, with most repairs running $400 – $1,800 installed depending on the section and material. If you’re reading this, you’ve likely spotted a leak, a lifted shingle, or a rusted flashing and you want to know exactly what it’ll take to fix it. The short version: we can usually match your Barrette profile same week, quote it in writing before work begins, and leave the job site cleaner than we found it. Barrette panels and trim are common on San Antonio homes built in the last 15 years, and we see the same failure patterns repeat across Alamo Heights, Stone Oak, and the older neighborhoods near the Pearl: gable trim loosening after wind, ridge caps cracking under heat, and screws backing out where the roof meets the fascia.
Which Barrette Models This Applies To
Barrette manufactures a few distinct roofing-related product lines that end up on San Antonio houses: the RDI railing and decking systems, Barrette Outdoor Living fascia and soffit trim, and the PVC and aluminum profiles that show up as gable trim, ridge caps, and corner posts. The gotcha we run into most often is that homeowners assume all white trim is the same profile. It isn’t. Barrette’s trim line includes multiple widths (typically 6-inch, 8-inch, and 10-inch fascia), and the profile shape changed subtly between the 2014 and 2020 runs, which means a 2015-era corner post will not seat cleanly against a 2022-era fascia board without a visible step. We check the underside stamp or label before ordering anything, and when the stamp has faded we measure the profile depth and the reveal, then match by those numbers rather than by a photo from your phone.
OEM Barrette trim pieces are worth the modest premium on visible gable ends and ridge lines because the color match is exact. For hidden pieces (starter strips, hidden clips), a quality aftermarket equivalent does the same job and saves real money. We’ll tell you which is which before you spend a dollar.
Styles & brands we work with
Signs Your Barrette Roofing Is Failing
- Gable trim pulling away from the fascia. San Antonio gets 30 – 40 mph gusts during spring storms, and Barrette’s aluminum gable trim is nailed at wider intervals than it should be on many original installs. When the trim starts to flutter, water rides behind it into the roof deck. This is the single most common Barrette-specific repair we make each spring.
- White or tan staining down the face of the trim. That’s oxidation from the factory-applied coating wearing through, and once it starts, it spreads fast under Texas sun. Pinpoint rust at a screw head or seam is the warning sign; broad chalky streaks mean the piece is past surface cleaning.
- A section of ridge cap that’s lifted at one end. Expansion and contraction in a San Antonio summer can work the original fasteners loose. The cap looks fine at a glance, but a lifted end lets wind catch the panel and tear the whole run.
- Loose or missing screws at the fascia-to-roof transition. Older Barrette installs used zinc-coated screws that fail after 8 – 10 years of heat and humidity. The PVC trim stays put, but the screw heads snap off inside the profile and the trim separates from the roof edge.
- Water staining inside the attic near the gable wall. By the time it shows indoors, the trim has usually been failing for a season or more. The water follows the gable trim down and pools where the rafter meets the top plate.
Replacement Cost & What’s Included
In San Antonio, a focused Barrette trim or ridge-cap replacement runs $400 – $1,800 installed. That price range covers the part itself, removal of the failed section, the new OEM or aftermarket piece matched to your existing profile, and disposal of everything we take off. A single 10-foot fascia replacement on a one-story home typically lands at the lower end; a full gable-end trim package with ridge caps and corner posts on a two-story home lands at the upper end.
Every quote is written down before work starts, with the part number and the labor broken out line by line. You sign that number, and that’s the number you pay. No supplements after we open the roof up unless we find damage we can’t see from the ground and you approve the change yourself. Our workmanship on Barrette parts is covered under the 365-Day Done Right Promise: if it’s not done right, we make it right.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely handle diagnosis: take photos of the trim from ground level, note where water appears after rain, and check for loose pieces you can reach from a ladder on flat ground. What we would not recommend doing yourself is working on a pitched roof over 6/12, especially on a two-story home. Barrette trim is aluminum and PVC, which feels lightweight, but the fall risk is the same as standing on any roof in San Antonio. The most common DIY mistakes we fix are mismatched profile sizes ordered from a photo and screws driven too deep through the PVC face. If you’re comfortable on a ladder and the repair is a flat, reachable fascia section, we’re happy to sell you the right part and walk you through it. For anything on the roof slope itself, call us at (432) 233-0976 and we’ll handle the ladder work.
FAQs
A correctly installed Barrette aluminum or PVC trim piece lasts 15 – 25 years in San Antonio’s climate, with color coating usually the first thing to fail rather than the material itself. Heat and UV degrade the factory coating faster than the aluminum or PVC structure, which is why a 12-year-old home can have structurally sound trim that has started to chalk. Call (432) 233-0976 and we’ll tell you whether your trim is at touch-up stage or replacement stage.
Sometimes, yes. Loose screws can be re-torqued, small dents can be left alone if they’re not catching water, and minor caulk failures at a seam can be resealed. Bent or cracked trim, rust-through, and any piece that has separated from the roof edge should be replaced. We’ll photograph the damage and give you an honest recommendation, not a pitch.
Most single-section replacements the crew can complete in one day. A full gable-end replacement with new ridge caps and corner posts usually takes two days. We’ll tell you the schedule when we give you the written quote, and we’ll protect the interior with drop cloths and shoe covers while we work.
We stock the most common Barrette fascia widths and the matching corner posts and ridge caps on the truck, and we can order any uncommon profile through our supplier network in San Antonio, usually within three to five business days. KraftMaid, Cambria, and Silestone options are also available when your project expands to the kitchen or bath. Call (432) 233-0976 with your trim width and we’ll tell you what’s in hand today.
Ready to Get Your Barrette Roofing Fixed?
Call (432) 233-0976 and you’ll reach a live person, not a voicemail box. We’ll ask a few questions about your Barrette trim, give you a range over the phone, and schedule a time to come see it in person. As Graham Stein puts it: write it down, price it once, do it right. The written quote you sign is the price you pay, and the crew will leave your San Antonio home with drop cloths picked up and a photo of the clean-up in hand before we go.
Written by Graham Stein, Owner, Elmstead Remodeling San Antonio at Elmstead Remodeling San Antonio, serving San Antonio and nearby areas.
