Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Windows & Doors: The San Antonio Owner’s Guide
KraftMaid does not manufacture its own windows or doors, which means the KraftMaid name you have on your cabinetry does not correspond to a dedicated KraftMaid window or door line. What most San Antonio homeowners actually have is a KraftMaid kitchen or bath with windows and doors from a separate manufacturer, and the failed part is usually a hinge, a window balance, a door roller, or weatherstripping on that separate unit. We stock and install replacement hardware for the window and door brands commonly paired with KraftMaid cabinetry, with installed hardware typically running $150 to $450 per window or door depending on the part and access. A binding estimate, written down before we order a single part, is always free.
Which KraftMaid Models This Applies To
Because KraftMaid focuses on cabinetry and not fenestration, the parts we match are for the windows and doors in homes where KraftMaid cabinets were installed. That covers most builder-grade and mid-range window lines in San Antonio homes from the early 2000s forward: single-hung and double-hung vinyl windows, sliding patio doors, and hinged French doors. The compatibility gotcha most owners hit is that a vinyl window’s balance system is sized to the exact sash weight and height, so a balance from a 36-inch window will not work on a 34-inch window even if both are “the same brand.” We identify the correct part by the window dimensions written on the top edge of the sash, the manufacturer label on the frame, and the stamped series code on the existing hardware. For KraftMaid-adjacent kitchen windows, the sash weight is the spec that matters most. OEM parts keep the original manufacturer warranty intact. Quality aftermarket equivalents generally cost 30% to 50% less and work well for hardware that sits outside the glazing seal, like rollers, locks, and balances. We tell you which one we recommend and why before you commit.
Styles & brands we work with
Signs Your KraftMaid Windows & Doors Is Failing
- The window sash drops when released, or won’t stay up. The constant-force balance or block-and-tackle balance has lost tension, which San Antonio’s summer attic heat accelerates by drying out the internal coil lubrication. This is the single most common window repair we see in older homes near Alamo Heights and Castle Hills.
- The sliding door grinds or catches halfway. Rollers have flat-spotted from years of fine dust and grit working into the track. San Antonio’s dry summers put a lot of particulate in the air, and it finds its way into roller bearings.
- You feel a draft along the edges even when the window is locked. The weatherstripping has compressed permanently or torn, usually along the meeting rail on double-hung windows. This is a material failure, not an installation error, and it is one of the cheapest parts to replace.
- The window lock or casement crank turns without moving the sash. The gear teeth inside the operator or lock have stripped. This tends to happen on casement windows that get opened and closed daily in kitchens, where KraftMaid cabinets are most common.
- The door won’t latch without lifting or pulling hard. Hinge screws have stripped or the door slab has settled. Before replacing the door, we usually re-hang it with longer screws into the framing, which fixes about 7 out of 10 cases.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For window hardware, expect an installed price range of $150 to $450 per window in San Antonio. Sliding glass door roller and track work generally runs $200 to $600. A full window replacement, when the frame itself is damaged or the glass has failed, runs $4,500 to $15,000 for a typical home here, which falls in line with our window replacement pricing. What drives the range on hardware is access: a first-floor kitchen window over tile counters takes less time than a second-story window over a roofline. Every hardware quote includes the part, the labor, the cleanup. Drop cloths go down before any work starts, shoe covers at the door, and you get a photo of the clean-up before the crew leaves. The work itself is covered under our 365-Day Done Right Promise: if it is not done right, we make it right.
DIY or Call Us?
Window balances, door rollers, and weatherstripping all operate under tension or compression. A balance assembly can hold enough stored energy to injure a hand if released incorrectly. We do not recommend opening a balance channel or removing a patio door slab as a weekend DIY project. What an owner can safely do is clean the door track, check for loose screws on the hinge side, and note the window dimensions and any visible manufacturer label before calling. That information helps us bring the right part on the first trip. If you would rather have a written price for the full repair, call (432) 233-0976. We will walk the job, write down the scope, and price it before any work starts. Graham Stein still writes every scope of work down before a single tool leaves the truck, because a part match only matters if the price you signed is the price you pay.
FAQs
Most window balances last 8 to 15 years here, and door rollers last 6 to 12 years depending on dust exposure and usage. San Antonio’s heat and grit shorten the lifespan compared to coastal climates, especially on western-facing windows. If your windows are older than 10 years and the hardware is original, expect to replace balances before the glazing itself fails. Call (432) 233-0976 and we can confirm the age and condition during a free estimate.
Door rollers can sometimes be cleaned and re-lubricated, but most window balances and stripped gear mechanisms are not repairable in a way that lasts. The internal springs and nylon parts are not sold individually. If you want a repair that holds up, plan on a part replacement. We will tell you if a repair is actually viable before recommending a part, and the written quote you sign is what you pay.
Most single-window balance or door roller replacements take 30 to 60 minutes once the right part is on site. A full door re-hang takes about two hours. The estimate visit is the real time investment, and it is free, because getting the part identified correctly is what keeps the job from going sideways.
We carry common window balances, roller assemblies, and weatherstripping profiles on the truck for the window and door lines we see most often in San Antonio. For less common series, like specific old-growth builder windows, we order OEM parts during the estimate phase. We also handle parts for other brands in the home, including Cambria, Silestone, and Kohler.
Written by Graham Stein, Owner, Elmstead Remodeling San Antonio at Elmstead Remodeling San Antonio, serving San Antonio and nearby areas.
